लाइव MCQ प्रैक्टिस सहायक अभियंता (विद्युत), वर्ग-2, सड़क Master Question Paper (BPB) - Technical Section (Series M) 180 MCQs · एक विकल्प चुनें
Sign in होने पर progress आपके SRO profile में सेव होती है।
निम्नलिखित में से कौन सा AC सर्किट में शिखर मान का सही प्रतिनिधित्व है?
A आरएमएस मूल्य/पीक फैक्टर
B आरएमएस मूल्य*फॉर्म फैक्टर
C आरएमएस मूल्य/फॉर्म फैक्टर
D आरएमएस मूल्य*पीक फैक्टर
अगला MCQ ↓ Electrical Engineering · AC Fundamentals
What is the direction of the electric field at a point?
A Along the line perpendicular to the electric field
B Along the line tangent to the electric field
C Electric field has no direction
D Electric field has a random direction
अगला MCQ ↓ Electrical Engineering · Electric Field
What is the number of primary turns in a 200/1000V transformer if the emf per turn is 10V?
A 5
B 10
C 20
D 40
अगला MCQ ↓ Electrical Engineering · Transformers
How many electrons will constitute 2 Coulombs of electric charge?
A 6.24 × 10¹⁸ electrons
B 12.48 × 10¹⁸ electrons
C 1.602 × 10¹⁹ electrons
D 3.204 × 10¹⁹ electrons
अगला MCQ ↓ Electrical Engineering · Electric Charge
How does induced emf in DC motor react to supply voltage?
A It will aid the supply voltage
B It will be double the supply voltage
C It will oppose the supply voltage
D It will be half of the supply voltage
अगला MCQ ↓ Electrical Engineering · DC Machines
How many cycles will an AC signal make in 2 seconds if its frequency is 100Hz?
A 50
B 100
C 150
D 200
अगला MCQ ↓ Electrical Engineering · AC Fundamentals
What will be the current density of a metal if a current of 30A is passed through a cross-sectional area of 0.5m2?
A 7.5 A/m2
B 15 A/m2
C 60 A/m2
D 120 A/m2
अगला MCQ ↓ Electrical Engineering · Current and Current Density
वह पदार्थ जिसकी सापेक्ष पारगम्यता मुक्त स्थान की पारगम्यता से कम है _____________ है।
A प्रतिचुम्बकीय
B अनुचुम्बकीय
C लौहचुम्बकीय
D कोई चुंबकीय पदार्थ नहीं
अगला MCQ ↓ Electrical Engineering · Magnetic Materials
प्रतिचुंबकीय पदार्थों की सापेक्ष पारगम्यता _____________ होती है।
A 1 से बड़ा
B 1 से कम
C 1 के बराबर
D शून्य
अगला MCQ ↓ Electrical Engineering · Magnetic Materials
What happens to the MMF when the magnetic flux decreases?
A Increases
B Decreases
C Remains constant
D Becomes zero
अगला MCQ ↓ Electrical Engineering · Magnetic Circuits
Can we apply Kirchhoff’s law to magnetic circuits?
A Yes
B No
C Depends on the circuit
D Insufficient information provided
अगला MCQ ↓ Electrical Engineering · Magnetic Circuits
KCL is based on the fact that
A There is a possibility for a node to store energy
B There cannot be an accumulation of charge at a node
C Charge accumulation is possible at node
D Charge accumulation may or may not be possible
अगला MCQ ↓ Electrical Engineering · Kirchhoff's Laws
आदर्श प्रेरक में शक्ति अपव्यय है
A अधिकतम
B न्यूनतम
C शून्य
D परिमित मूल्य
अगला MCQ ↓ Electrical Engineering · AC Circuits
To obtain wide bandwidth, network is designed with which of the following?
A High Q factor
B Low Q factor
C Unity Q factor
D Zero Q factor
अगला MCQ ↓ Electrical Engineering · Resonance
Find V_AB if i_AB = 5 A.
A 32.76V
B 35.56V
C 36.12V
D 34.21V
अगला MCQ ↓ Electrical Engineering · Resistive Networks
Q16
Moderate 2025 ✓ Verified
↗
If 4 equations are required to describe a circuit by Mesh-Current method and there are n nodes, then how many branches are there in the network?
A n + 5
B n + 3
C n
D n − 1
अगला MCQ ↓ Electrical Engineering · Graph Theory
डेल्टा-कनेक्टेड लोड में, लाइन वोल्टेज और चरण वोल्टेज के बीच संबंध होता है
A लाइन वोल्टेज
B लाइन वोल्टेज
C लाइन वोल्टेज = चरण वोल्टेज
D लाइन वोल्टेज
अगला MCQ ↓ Electrical Engineering · Three-Phase Circuits
यूनिट आवेग फ़ंक्शन और यूनिट रैंप फ़ंक्शन के बीच क्या संबंध है?
A आर = डीडी(टी)/डीटी
B डी = डॉ/डीटी
C δ(t) = d²r(t)/dt²
D आर = डी2(डी)/डीटी2
अगला MCQ ↓ Electrical Engineering · Elementary Signals
Q19
Moderate 2025 ✓ Verified
↗
1 mH और 2 mH के स्व-प्रेरकत्व वाली दो कुंडलियाँ परस्पर जुड़ी हुई हैं। अधिकतम संभव पारस्परिक प्रेरण ___________ है
A 1.414 एमएच
B 2 एमएच
C 1 एमएच
D 5.5 एमएच
अगला MCQ ↓ Electrical Engineering · Magnetic Coupling
एक कुंडल में प्रतिरोध R और प्रेरकत्व L है। ω = ∞ पर, वोल्टेज और धारा के बीच चरण कोण _____________ है
A 0°
B 180°
C 45°
D 90°
अगला MCQ ↓ Electrical Engineering · AC Circuits
नीचे दिखाए गए सर्किट में, Z-पैरामीटर Z₁₂ खोजें।
A 15
B 10
C 5
D 1
अगला MCQ ↓ Electrical Engineering · Two-Port Networks
Q22
Moderate 2025 ✓ Verified
↗
घूमने वाली विद्युत मशीनरी में विद्युत चुम्बकीय टॉर्क तब मौजूद होता है जब ________
A स्टेटर और रोटर वाइंडिंग दोनों में करंट प्रवाहित होता है
B वायु अन्तराल एकसमान है
C स्टेटर वाइंडिंग अकेले ही करंट प्रवाहित करती है
D रोटर वाइंडिंग अकेले ही करंट प्रवाहित करती है
अगला MCQ ↓ Electrical Engineering · Electromechanical Energy Conversion
A 400-V, 1000-A, lap wound DC machine has 10 poles, 860 armature conductors. The number of conductors in the pole face to give full compensation if pole face covers 70% of pole span is
A 3010
B 4300
C 2400
D 2800
अगला MCQ ↓ Electrical Engineering · DC Machines
Q24
Moderate 2025 ✓ Verified
↗
__________ परीक्षण का उपयोग कर्षण मोटर की दक्षता निर्धारित करने के लिए किया जाता है।
A हॉपकिंसन
B मंदता
C मैदान
D स्विनबर्न
अगला MCQ ↓ Electrical Engineering · DC Motors
वायु अंतराल रेखा _________ का प्रतिनिधित्व करती है
A डीसी मशीन के वायु अंतराल का चुंबकीय व्यवहार
B प्रेरण मशीन के वायु अंतराल का चुंबकीय व्यवहार
C लौह कोर का चुंबकीय व्यवहार
D सभी का उल्लेख किया गया है
अगला MCQ ↓ Electrical Engineering · DC Machines
The active power delivered by an alternator will _______ when the prime mover input is increased for the alternator connected to infinite bus bar.
A remain constant
B decrease
C increase
D no relation exists between the power and prime mover droop characteristic
अगला MCQ ↓ Electrical Engineering · Synchronous Machines
Q27
Moderate 2025 ✓ Verified
↗
एक सिंक्रोनस मशीन में स्टेटर पर फ़ील्ड वाइंडिंग और रोटर पर पॉलीफ़ेज़ आर्मेचर वाइंडिंग होती है। स्थिर अवस्था में, इसके वायु अंतराल क्षेत्र के लिए निम्नलिखित में से कौन सा सत्य नहीं है?
A स्टेशनरी w.r.t. स्टेटर
B दोगुनी गति से घूम रहा है Ns w.r.t. रोटर
C रोटर के विपरीत दिशा में घूमना
D Ns w.r.t पर घूम रहा है रोटर
अगला MCQ ↓ Electrical Engineering · Synchronous Machines
Q28
Moderate 2025 ✓ Verified
↗
इन दिनों अल्टरनेटर को __________ के लिए बड़े वायु अंतराल के लिए डिज़ाइन किया गया है।
A स्थिर समानांतर संचालन
B उच्च स्थिरता सीमा
C साइनसोइडल एमएमएफ वितरण
D सभी का उल्लेख किया गया है
अगला MCQ ↓ Electrical Engineering · Synchronous Machines
An induction motor can be said analogous to _________
A Synchronous motor
B Transformer
C Universal motor
D Stepper motor
अगला MCQ ↓ Electrical Engineering · Induction Motors
While conducting open circuit test and short circuit test on a transformer, status of low voltage and high voltage windings will be such that in ____________
A OC test − h.v. open, SC test − l.v. short-circuited
B OC test − l.v. open, SC test − h.v. short-circuited
C OC test − l.v. open, SC test − l.v. short-circuited
D OC test − h.v. open, SC test − h.v. short-circuited
अगला MCQ ↓ Electrical Engineering · Transformers
एक 2000/1000/500 तीन वाइंडिंग ट्रांसफार्मर का उपयोग 3000V की आपूर्ति के साथ ऑटो ट्रांसफार्मर के रूप में किया जाना है। 3500 वी पर 1050 केवीए के दो लोड और 1000 वी पर 180 केवीए का दूसरा लोड। आपूर्ति की गई कुल केवीए होगी
A 1230 केवीए
B 1440 केवीए
C 1680 केवीए
D 1150 केवीए
अगला MCQ ↓ Electrical Engineering · Transformers
Q32
Moderate 2025 ✓ Verified
↗
दो एकल चरण ट्रांसफार्मर ए और बी अलग-अलग प्रतिबाधा और समान एक्स/आर अनुपात वाले समानांतर में काम कर रहे हैं। फिर __________
A A का पीएफ B से कम है
B B का पीएफ B से कम है
C कम पावर फैक्टर कोण
D दोनों एक ही पावर फैक्टर पर काम करते हैं
अगला MCQ ↓ Electrical Engineering · Transformers
एक वेक्टर को सोलेनॉइडल कहा जाता है जब यह
A विचलन शून्य है
B विचलन ही एकता है
C कर्ल शून्य है
D कर्ल एकता है
अगला MCQ ↓ Electrical Engineering · Vector Calculus
Q34
Moderate 2025 ✓ Verified
↗
A = x i y j z k के लिए स्टोक के प्रमेय का मान ज्ञात कीजिए। समारोह की स्थिति होगी
A सोलेनोइडल
B भिन्न
C घूर्णी
D कर्लफ्री
अगला MCQ ↓ Electrical Engineering · Vector Calculus
Q35
Moderate 2025 ✓ Verified
↗
शक्ति ज्ञात कीजिए, दी गई ऊर्जा E = 2J और धारा घनत्व J = x2 x = 0 और x = 1 से भिन्न होता है।
A 1/3
B 2/3
C 1
D 4/3
अगला MCQ ↓ Electrical Engineering · Energy and Power
Q36
Moderate 2025 ✓ Verified
↗
Evaluate the surface integral ∫∫ (3x i + 2y j). dS, where S is the sphere given by x² + y² + z² = 9.
A 120 π
B 180 π
C 240 π
D 300 π
अगला MCQ ↓ Electrical Engineering · Vector Calculus
Q37
Moderate 2025 ✓ Verified
↗
R = 2m पर σ = 5, R = 4m पर σ = − 2 और R = 5m पर σ = − 3 के साथ तीन चार्ज बेलनाकार शीट तीन स्थानों में मौजूद हैं। R = 3m पर फ्लक्स घनत्व ज्ञात कीजिए।
A 3
B 10/3
C 11/3
D 4
अगला MCQ ↓ Electrical Engineering · Gauss Law
Q38
Moderate 2025 ✓ Verified
↗
सातत्य समीकरण किन दो नियमों का संयोजन है?
A ओम का नियम और गॉस का नियम
B एम्पीयर नियम और गॉस नियम
C ओम का नियम और एम्पीयर का नियम
D मैक्सवेल नियम और एम्पीयर नियम
अगला MCQ ↓ Electrical Engineering · Maxwell Equations
28C आवेश और 12 mF धारिता वाली धातु की प्लेट की क्षमता की गणना करें।
A 3.33 k ओम
B 2.33 k ओम
C 3.33 एम ओम
D 2.33 एम ओम
अगला MCQ ↓ Electrical Engineering · Electrostatics
Calculate the emf when the flux is given by 3sin t + 5cos t.
A 3cos t − 5sin t
B − 3cos t + 5sin t
C − 3sin t − 5cos t
D 3cos t + 5sin t
अगला MCQ ↓ Electrical Engineering · Electromagnetic Induction
Q41
Moderate 2025 ✓ Verified
↗
Find the inductance of a coil with permeability 3.5, turns 100 and length 2m. Assume the area to be thrice the length.
A 131.94 mH
B 94.131 mH
C 131.94 H
D 94.131 H
अगला MCQ ↓ Electrical Engineering · Magnetic Circuits
Calculate the conduction current density when the resistivity of a material with an electric field of 5 units is 4.5 units.
A 22.5
B 4.5/5
C 5/4.5
D 9.5
अगला MCQ ↓ Electrical Engineering · Conduction and Current Density
डिजिटल इलेक्ट्रॉनिक्स में एक लॉजिक गेट कई अन्य लॉजिक गेट्स को कब चला सकता है?
A जब इसका आउटपुट प्रतिबाधा कम हो और इनपुट प्रतिबाधा कम हो
B जब इसका आउटपुट प्रतिबाधा अधिक हो और इनपुट प्रतिबाधा अधिक हो
C जब इसका आउटपुट प्रतिबाधा अधिक हो और इनपुट प्रतिबाधा कम हो
D जब इसका आउटपुट प्रतिबाधा कम हो और इनपुट प्रतिबाधा अधिक हो
अगला MCQ ↓ Electrical Engineering · Logic Families
Q44
Moderate 2025 ✓ Verified
↗
इनमें से कौन सा त्रुटि-पता लगाने वाला कोड डिजिटल इलेक्ट्रॉनिक उपकरणों में दोहरी त्रुटियां ढूंढने में सक्षम बनाता है?
A समता विधि
B चेकसम विधि
C बिट जनरेशन विधि
D ऑड-ईवन पद्धति
अगला MCQ ↓ Electrical Engineering · Digital Codes
यदि A और B आधे योजक के इनपुट हैं, तो योग __________ द्वारा दिया जाता है
A ए और बी
B ए या बी
C ए एक्सओआर बी
D एक भूतपूर्व नॉर बी
अगला MCQ ↓ Electrical Engineering · Combinational Logic
लॉजिक सर्किट की व्यवस्थित कमी _______________ द्वारा पूरी की जाती है
A प्रतीकात्मक कमी
B टीटीएल तर्क
C बूलियन बीजगणित का उपयोग करना
D सत्य तालिका का उपयोग करना
अगला MCQ ↓ Electrical Engineering · Boolean Algebra
10 में से 1 बीसीडी डिकोडर के लिए कितने इनपुट की आवश्यकता होती है?
A 4
B 8
C 10
D 2
अगला MCQ ↓ Electrical Engineering · Combinational Logic
What is the maximum possible range of bit-count specifically in n-bit binary counter consisting of ‘n’ number of flip-flops?
A 0 to 2n
B 0 to 2n + 1
C 0 to 2n − 1
D 0 to 2n+1/2
अगला MCQ ↓ Electrical Engineering · Sequential Logic
A 12 MHz clock frequency is applied to a cascaded counter containing a modulus-5 counter, a modulus-8 counter and a modulus-10 counter. The lowest output frequency possible is ________
A 10 kHz
B 20 kHz
C 30 kHz
D 60 kHz
अगला MCQ ↓ Electrical Engineering · Sequential Logic
A 4-bit ripple counter consists of flip-flops, where each have a propagation delay from clock to Q output of 15 ns. For the counter to recycle from 1111 to 0000, it takes a total of ________
A 15 ns
B 30 ns
C 45 ns
D 60 ns
अगला MCQ ↓ Electrical Engineering · Sequential Logic
Q51
Moderate 2025 ✓ Verified
↗
एक द्विदिशात्मक 4-बिट शिफ्ट रजिस्टर निबल 1110 को संग्रहीत कर रहा है। इसका इनपुट कम है। निबल 0111 सीरियल डेटा-इनपुट लाइन पर दर्ज होने की प्रतीक्षा कर रहा है। दो क्लॉक पल्स के बाद, शिफ्ट रजिस्टर ________ संग्रहीत कर रहा है
A 1110
B 0111
C 1011
D 1001
अगला MCQ ↓ Electrical Engineering · Sequential Logic
Q52
Moderate 2025 ✓ Verified
↗
बिट्स 10110111 के समूह को प्रारंभिक स्थिति 11110000 के साथ 8-बिट समानांतर आउटपुट शिफ्ट रजिस्टर में क्रमिक रूप से (सबसे दाहिनी बिट पहले) स्थानांतरित किया जाता है। दो क्लॉक पल्स के बाद, रजिस्टर में ____________ होता है
A 10111000
B 10110111
C 11110000
D 11111100
अगला MCQ ↓ Electrical Engineering · Sequential Logic
Q53
Moderate 2025 ✓ Verified
↗
The output frequency related to the sampling interval of a frequency counter as _____________
A Directly with the sampling interval
B Inversely with the sampling interval
C More precision with longer sampling interval
D Less precision with longer sampling interval
अगला MCQ ↓ Electrical Engineering · Digital Measurement
बाहरी उपकरण के सीरियल प्रारूप के साथ समानांतर डेटा प्रारूप को इंटरफ़ेस करने के लिए किस प्रकार के उपकरण का उपयोग किया जा सकता है?
A यूएआरटी
B कुंजी मैट्रिक्स
C मेमोरी चिप
D समानांतर में शृंखला
अगला MCQ ↓ Electrical Engineering · Data Communication Interfaces
A 4-bit shift register that receives 4 bits of parallel data will shift to the ________ by ________ position for each clock pulse.
A Right, one
B Right, two
C Left, one
D Left, three
अगला MCQ ↓ Electrical Engineering · Sequential Logic
In the case of two-transistor model (T1 & T2) of GTO with anode−short, the anode−short is placed between the
A emitter of T1 and T2
B emitter of T1 and base of T2
C emitter of T1 and base of T1
D emitter of T1 and collector of T2
अगला MCQ ↓ Electrical Engineering · Thyristor Devices
एक स्टेप-डाउन डेल्टा-स्टार ट्रांसफार्मर, प्रति-चरण 5 टर्न अनुपात के साथ, 3-चरण, 1100 वी, 50 हर्ट्ज स्रोत से खिलाया जाता है। 3-पल्स प्रकार के रेक्टिफायर के माध्यम से इस ट्रांसफार्मर का सेकेंडरी 10 Ω का आर लोड फ़ीड करता है। लोड धारा (चरण) का अधिकतम मान ज्ञात कीजिए।
A √2 × 22 ए
B 1×11 ए
C √2 × 11 ए
D 1×22 ए
अगला MCQ ↓ Electrical Engineering · Rectifiers
Q58
Moderate 2025 ✓ Verified
↗
In non-circulating current mode dual converters, the circulating current is avoided by
A Connecting a series reactor
B Maintaining α1 + α2 = 180°
C Operating only one converter
D Adding an extra SCR
अगला MCQ ↓ Electrical Engineering · Converters
एकल-पल्स चौड़ाई मॉड्यूलेशन विधि में, आउटपुट वोल्टेज तरंग नकारात्मक आधे चक्र में ____________ के बारे में सममित है।
A 2π
B 3π/2
C π/2
D 3π/4
अगला MCQ ↓ Electrical Engineering · Inverters
Q60
Moderate 2025 ✓ Verified
↗
In the case of a single−pulse width modulation with the pulse width = 2d, to eliminate the nth harmonic from the output voltage
A d = π
B 2d = π
C nd = π
D nd = 2π
अगला MCQ ↓ Electrical Engineering · Inverters
AC वोल्टेज नियंत्रकों का उपयोग __________ अनुप्रयोगों में किया जाता है।
A बिजली उत्पादन
B विद्युत तापन
C कन्वेयर बेल्ट गति
D विद्युत पारेषण
अगला MCQ ↓ Electrical Engineering · AC Voltage Controllers
Q62
Moderate 2025 ✓ Verified
↗
In a N-stage sequence controller, each secondary is rated for __________
A n × Vs
B Vs
C Vs/n
D Vs × (n − 1)
अगला MCQ ↓ Electrical Engineering · High Voltage Generation
The single−phase mid-point type cycloconverter uses __________ number of SCRs.
A 4
B 8
C 6
D 2
अगला MCQ ↓ Electrical Engineering · Cycloconverters
Two six pulse converters used for bipolar HVDC transmission system are rated at 1000 MW, ± 200 kV. What is the DC transmission voltage?
A 200 kV
B 400 kV
C 500 kV
D 100 kV
अगला MCQ ↓ Electrical Engineering · HVDC Transmission
A single−phase AC switch is used in between a 230 V source and load of 2 kW and 0.8 lagging power factor. Determine the rms current rating required by the SCR. Use the factor of safety = 2.
A 10.87 A
B 87 A
C 21.74 A
D 32 A
अगला MCQ ↓ Electrical Engineering · AC Controllers
Q66
Moderate 2025 ✓ Verified
↗
Choose the incorrect statement.
A SMPS is less sensitive to input voltage variations
B SMPS is smaller as compared to rectifiers
C SMPS has low input ripple
D SMPS is a source of radio interference
अगला MCQ ↓ Electrical Engineering · Switched Mode Power Supplies
Q67
Moderate 2025 ✓ Verified
↗
Which of the following signals is monotonic?
A x(t) = t³− 2t
B x(t) = sin(t)
C x(t) = sin²(2t) + cos²(2t) − 2t
D x(t) = log(cos(t))
अगला MCQ ↓ Electrical Engineering · Signal Classification
x(t) को गैर-आवधिक संकेत कब कहा जाता है?
A यदि समीकरण x (t) = x (t T) T के सभी मानों के लिए संतुष्ट है
B यदि समीकरण x (t) = x (t T) T के केवल एक मान के लिए संतुष्ट है
C यदि समीकरण x (t) = x (t T) T के किसी भी मान के लिए संतुष्ट नहीं है
D यदि समीकरण x (t) = x (t T) केवल T के विषम मानों के लिए संतुष्ट है
अगला MCQ ↓ Electrical Engineering · Signal Classification
Determine the discrete−time signal: x(n) = 1 for n ≥ 0 and x(n) = 0 for n < 0.
A Unit ramp sequence
B Unit impulse sequence
C Exponential sequence
D Unit step sequence
अगला MCQ ↓ Electrical Engineering · Discrete-Time Signals
Q70
Moderate 2025 ✓ Verified
↗
k के किन मानों के लिए निम्नलिखित प्रणाली स्थिर है, y = (k² − 3k − 4)log(x) syn(x)?
A के = 1, 4
B के = 2, 3
C के = 5, 4
D के = 4, − 1
अगला MCQ ↓ Electrical Engineering · Systems
A 440 V, 50 Hz AC source supplies a series LCR circuit with a capacitor and a coil. If the coil has 100 mΩ resistance and 15 mH inductance, then at a resonance frequency of 50 Hz, the half power frequencies of the circuit are ______________
A 50.53 Hz, 49.57 Hz
B 52.12 Hz, 49.8 Hz
C 55.02 Hz, 48.95 Hz
D 50 Hz, 49 Hz
अगला MCQ ↓ Electrical Engineering · RLC Circuits
एक सिग्नल e^(−at) syn (ωt) एक वास्तविक रैखिक समय अपरिवर्तनीय प्रणाली का इनपुट है। दिया गया K और ∅ स्थिरांक हैं, सिस्टम का आउटपुट Ke^(−bt) syn (vt ∅) के रूप में होगा। निम्नलिखित में से सही कथन __________ है
A b को a के बराबर नहीं होना चाहिए लेकिन v को ω के बराबर होना चाहिए
B v को ω के बराबर होना आवश्यक नहीं है लेकिन b को a के बराबर होना चाहिए
C b, a के बराबर होना चाहिए और v, ω के बराबर होना चाहिए
D b का a के बराबर होना आवश्यक नहीं है और v का ω के बराबर होना आवश्यक नहीं है
अगला MCQ ↓ Electrical Engineering · LTI Systems
Q73
Moderate 2025 ✓ Verified
↗
एक आवधिक वर्ग तरंग -1 से 1 और अवधि = 2 इकाइयों तक के आयताकार दालों द्वारा बनाई जाती है। इस तरंगरूप के लिए 7वें हार्मोनिक में शक्ति और 5वें हार्मोनिक में शक्ति का अनुपात ____________ के बराबर है
A 1
B 0.5
C 2
D 2.5
अगला MCQ ↓ Electrical Engineering · Fourier Series
Q74
Moderate 2025 ✓ Verified
↗
फूरियर अभिसरण प्रमेय कब लागू होता है?
A अनंत श्रृंखला सीमा
B सतत कार्य सीमा
C असतत कार्य सीमा
D बिंदु सीमा तोड़ें
अगला MCQ ↓ Electrical Engineering · Fourier Series
Which of the following waves has the highest value of peak factor?
A Square wave
B Sine wave
C Half wave rectified sine wave
D Triangular wave
अगला MCQ ↓ Electrical Engineering · Waveform Parameters
एक आगमनात्मक सर्किट का समय स्थिरांक
A प्रेरकत्व के बढ़ने और प्रतिरोध के घटने के साथ बढ़ता है
B प्रेरकत्व की वृद्धि और प्रतिरोध की वृद्धि के साथ बढ़ता है
C प्रेरण के घटने और प्रतिरोध के घटने के साथ बढ़ता है
D प्रेरकत्व के घटने और प्रतिरोध के बढ़ने के साथ बढ़ता है
अगला MCQ ↓ Electrical Engineering · First-Order Circuits
Q77
Moderate 2025 ✓ Verified
↗
एक एलटीआई प्रणाली की आवेग प्रतिक्रिया जो निरंतर है H (t) = e−|t| प्रणाली ___________ है
A कारणात्मक एवं स्थिर
B कारणात्मक लेकिन स्थिर नहीं
C स्थिर लेकिन कारणात्मक नहीं
D न तो कारण और न ही स्थिर
अगला MCQ ↓ Electrical Engineering · LTI Systems
Q78
Moderate 2025 ✓ Verified
↗
Form factor is equal to peak factor in the case of
A Square wave
B Triangle wave
C Saw tooth wave
D Sinusoidal wave
अगला MCQ ↓ Electrical Engineering · Waveform Parameters
Which of the following reactances is eliminated first in synchronous generator just after the symmetrical fault?
A Leakage reactance
B Damper winding reactance
C Armature winding reactance
D Field winding reactance
अगला MCQ ↓ Electrical Engineering · Fault Analysis
A transmission line Z = (2 + j8) Ω has 10% of the voltage regulation with the lagging load of 0.8. If the load is 0.707 leading, then the V.R. is ________ (Assume the current is same in both cases)
A − 6.63%
B − 5.77%
C − 10%
D − 8.63%
अगला MCQ ↓ Electrical Engineering · Transmission Lines
एक खुला पाइप 500 हर्ट्ज आवृत्ति के ट्यूनिंग कांटा के साथ प्रतिध्वनित होता है। यह देखा गया है कि खुले सिरे से 16 सेमी और 46 सेमी की दूरी पर दो क्रमिक नोड बनते हैं। पाइप में हवा में ध्वनि की गति है
A 230 मी/से
B 300 मी/से
C 320 मी/से
D 360 मी/से
अगला MCQ ↓ Electrical Engineering · Waves and Acoustics
400/33000 V के लाइन वोल्टेज अनुपात वाला एक तीन-चरण ट्रांसफार्मर स्टार-डेल्टा में जुड़ा हुआ है। 400V की ओर के CT का CT अनुपात 1000/5 है। 33000 पक्ष पर सीटी का अनुपात क्या होना चाहिए?
A 7/5
B 5/7
C 3/5
D 5/2
अगला MCQ ↓ Electrical Engineering · Protection
तीन चरण 20 एमवीए, 11 केवी अल्टरनेटर के न्यूट्रल को 5 ओम के प्रतिरोध के माध्यम से अर्थ किया जाता है। जब 1.5 ए का करंट असंतुलित हो तो रिले को संचालित करने के लिए सेट किया जाता है। सीटी का अनुपात 100/5 होता है। 90% वाइंडिंग की सुरक्षा के लिए अर्थिंग प्रतिरोध का न्यूनतम मान क्या होना चाहिए?
A 1.12 Ω
B 2.12 Ω
C 4.24 Ω
D 3.24 Ω
अगला MCQ ↓ Electrical Engineering · Protection
Q84
Moderate 2025 ✓ Verified
↗
A single−phase motor is connected to 400V, 50Hz supply. The motor draws a current of 31.7A at a power factor 0.7 lag. The additional reactive power (in VAR) to be supplied by the capacitor bank will be ___________
A 4756
B 4873
C 4299
D 9055.3
अगला MCQ ↓ Electrical Engineering · Power Factor Correction
Q85
Moderate 2025 ✓ Verified
↗
एक पृथक जनरेटर 20 मेगावाट, 50 हर्ट्ज की निरंतर अधिकतम शक्ति के साथ एक टरबाइन से जुड़ा हुआ है। जेनरेटर 8 मेगावाट के दो लोड से जुड़ा है, प्रत्येक 50 हर्ट्ज पर संचालित होता है। जेनरेटर में 5% ड्रॉप विशेषता है। यदि 6 मेगावाट का अतिरिक्त भार जोड़ा जाता है, तो आवृत्ति ___________ होगी
A 40.75
B 48.75
C 49.75
D 50.25
अगला MCQ ↓ Electrical Engineering · Load Frequency Control
यदि किसी विद्युत प्रणाली में दोष बिंदु पर सभी अनुक्रम वोल्टेज समान हैं, तो दोष __________ है
A एलएलजी दोष
B एलजी की गलती
C ग्राउंड फॉल्ट के लिए तीन चरण
D लाइन टू लाइन फाल्ट
अगला MCQ ↓ Electrical Engineering · Fault Analysis
Q87
Moderate 2025 ✓ Verified
↗
The characteristic equation of a control system is given by s(s + 4)(s² + 2s + s) + k(s + 1) = 0. What are the angles of the asymptotes for the root loci?
A 0°, 180°, 300°
B 0°, 120°, 240°
C 60°, 180°, 300°
D 120°, 180°, 240°
अगला MCQ ↓ Electrical Engineering · Root Locus
दूसरे क्रम प्रणाली की इकाई चरण प्रतिक्रिया = 1 − e^(−5t) − 5t e^(−5t) है। निम्नलिखित कथनों पर विचार करें: 1. कम नम प्राकृतिक आवृत्ति 5 रेड/सेकेंड है। 2. अवमंदन अनुपात है 1. 3. आवेग प्रतिक्रिया 25t e^(−5t) है। ऊपर दिए गए कथनों में से कौन सा सही है?
A केवल 1 और 2
B केवल 2 और 3
C केवल 1 और 3
D 1, 2 और 3
अगला MCQ ↓ Electrical Engineering · Second-Order Systems
Q89
Moderate 2025 ✓ Verified
↗
दावा (ए): एक पीआई नियंत्रक इकाइयों द्वारा सिस्टम के क्रम को बढ़ाता है लेकिन स्थिर स्थिति त्रुटि को कम करता है। कारण (आर): एक पीआई नियंत्रक या तो मूल बिंदु पर या नकारात्मक वास्तविक अक्ष पर वांछित बिंदु पर एक ध्रुव प्रस्तुत करता है।
A (ए) और (आर) दोनों सत्य हैं और (आर) (ए) का सही स्पष्टीकरण है
B (ए) और (आर) दोनों सत्य हैं लेकिन (आर) (ए) का सही स्पष्टीकरण नहीं है
C (ए) सच है लेकिन (आर) गलत है
D (ए) गलत है लेकिन (आर) सच है
अगला MCQ ↓ Electrical Engineering · Controllers
Q90
Moderate 2025 ✓ Verified
↗
Assertion (A): Routh criterion is in terms of array formulation which is more convenient to handle. Reason (R): This method is used to investigate the method of stability of higher order systems.
A Both (A) and (R) are true and (R) is the correct explanation of (A)
B Both (A) and (R) are true and (R) is not the correct explanation of (A)
C (A) is true but (R) is false
D (A) is false but (R) is true
अगला MCQ ↓ Electrical Engineering · Stability
The auto-correlation function of a rectangular pulse of duration T is
A A rectangular pulse of duration T
B A rectangular pulse of duration 2T
C A triangular pulse of duration T
D A triangular pulse of duration 2T
अगला MCQ ↓ Electrical Engineering · Signals and Systems
Q92
Moderate 2025 ✓ Verified
↗
The method of investigating the stability using Liapunov function is _____________
A The direct method
B The indirect method
C Not determined
D Always unstable
अगला MCQ ↓ Electrical Engineering · Nonlinear Control
For a unity feedback system, the open loop transfer function is G(s) = K(s + 2)/s² (s² + 7s + 12). What is the type of system?
A One
B Two
C Three
D Four
अगला MCQ ↓ Electrical Engineering · Steady-State Error
What is the response of the feedback function with open loop transfer function G(s) = 4/s(s + 5) and input is input step?
A 1 − 1/3(4e^(−t) − e^(−4t))
B 1 − 1/2(6e^(−t) − e^(−4t))
C 1 − 1/3(6e^(−t) − e^(−4t))
D 1 − 1/2(4e^(−t) − e^(4t))
अगला MCQ ↓ Electrical Engineering · Time Response
The open loop transfer function for a unit feedback system is G(s) = K/s(sT + 1). By what factor the amplitude gain K should be reduced so that the peak overshoot becomes 25% from 75%?
A 75
B 25
C 20
D 10
अगला MCQ ↓ Electrical Engineering · Transient Response
What is the need for a controller?
A Receive control signals
B Transmit control signals
C Modify control signals
D Create control signals
अगला MCQ ↓ Electrical Engineering · Controllers
What is the vectored address of RST-5?
A 0010 H
B 0032 H
C 0028 H
D 0030 H
अगला MCQ ↓ Electrical Engineering · 8085 Microprocessor
DAA instruction is used to perform which type of addition?
A BCD addition
B Excess-3 addition
C Binary addition
D Octal addition
अगला MCQ ↓ Electrical Engineering · 8085 Microprocessor
In the I/O mode, the 8255 ports work as
A Reset pins
B Set pins
C Programmable I/O ports
D Only output ports
अगला MCQ ↓ Electrical Engineering · 8255 PPI
Q100
Moderate 2025 ✓ Verified
↗
यदि पिन एसटीबी (स्ट्रोब इनपुट) का मान निम्न स्तर तक गिर जाता है
A इनपुट पोर्ट को इनपुट लैच में लोड किया जाता है
B इनपुट पोर्ट को आउटपुट लैच में लोड किया जाता है
C आउटपुट पोर्ट को इनपुट लैच में लोड किया जाता है
D आउटपुट पोर्ट को आउटपुट लैच में लोड किया जाता है
अगला MCQ ↓ Electrical Engineering · 8255 PPI
Q101
Easy 2025 ✓ Verified
↗
जब एक स्टैक सेगमेंट प्रारंभ किया जाता है, तब
A एसएस और एसपी प्रारंभ किए गए हैं
B केवल एसएस प्रारंभ किया गया है
C केवल SP आरंभीकृत है
D एसएस और एसपी को प्रारंभ करने की आवश्यकता नहीं है
अगला MCQ ↓ Electrical Engineering · 8086 Microprocessor
Q102
Moderate 2025 ✓ Verified
↗
मोड 2 में, यदि एन को गिनती मूल्य के रूप में लोड किया जाता है, तो (एन - 1) चक्र के बाद, आउटपुट कम हो जाता है
A 1 घड़ी चक्र
B 2 घड़ी चक्र
C 3 घड़ी चक्र
D 4 घड़ी चक्र
अगला MCQ ↓ Electrical Engineering · 8253/8254 Timer
Q103
Moderate 2025 ✓ Verified
↗
यदि शून्य शर्त संतुष्ट है, तो निष्पादन के लिए, जेएनजेड निर्देश लिया जाता है
A 1 घड़ी चक्र
B 2 घड़ी चक्र
C 3 घड़ी चक्र
D 4 घड़ी चक्र
अगला MCQ ↓ Electrical Engineering · Microprocessor Instructions
Q104
Easy 2025 ✓ Verified
↗
वह पिन जो सेट होने पर कमांड, अनुरोध और अस्थायी रजिस्टरों और आंतरिक प्रथम/अंतिम फ्लिपफ्लॉप को साफ़ करता है
A साफ़
B सेट
C एच.एल.डी.ए
D रीसेट करें
अगला MCQ ↓ Electrical Engineering · DMA Controller
Q105
Easy 2025 ✓ Verified
↗
संपूर्ण सॉफ्टवेयर सिस्टम को विभाजित किया गया है
A मुख्य कार्यक्रम
B यूनिट के प्रथम उपप्रसंस्करण के लिए रूटीन IRT2 को बाधित करें
C यूनिट के प्रथम उपप्रसंस्करण के लिए रूटीन IRT3 को बाधित करें
D सभी का उल्लेख किया गया है
अगला MCQ ↓ Electrical Engineering · Real-Time Software
Q106
Moderate 2025 ✓ Verified
↗
The highest priority usage than any other usage is
A Transfer with LOCK (active low) signal
B Hold request
C Processor extension data transfer
D Data transfer performed by EU (execution unit)
अगला MCQ ↓ Electrical Engineering · 8086/80286 Bus
Q107
Hard 2025 ✓ Verified
↗
वैध होल्ड अनुरोध पूरा होने के बाद ही सुनिश्चित किया जाता है
A 34 घड़ी चक्र
B 24 घड़ी चक्र और 80286 सेट है
C 34 घड़ी चक्र और 80286 सेट है
D 34 घड़ी चक्र और 80286 रीसेट है
अगला MCQ ↓ Electrical Engineering · 80286 Microprocessor
Q108
Hard 2025 ✓ Verified
↗
The number of idle states (Ti), that is allowed between two INTA cycles, to meet the 8259A speed and cascade address output delay is
A 1
B 2
C 3
D 4
अगला MCQ ↓ Electrical Engineering · 8259A PIC
Q109
Moderate 2025 ✓ Verified
↗
एचवीडीसी एलसीसी में ______________ होते हैं
A स्वतंत्रता की 1 डिग्री
B स्वतंत्रता की 2 डिग्री
C स्वतंत्रता की 5 डिग्री
D स्वतंत्रता की कई डिग्री
अगला MCQ ↓ Electrical Engineering · HVDC Transmission
Q110
Easy 2025 ✓ Verified
↗
कुशल LCC HVDC कन्वर्टर्स आम तौर पर __________ का उपयोग करते हैं
A थाइरिस्टर
B पारा वाल्व
C डायोड
D यांत्रिक स्विच
अगला MCQ ↓ Electrical Engineering · HVDC Transmission
Q111
Easy 2025 ✓ Verified
↗
उच्च वोल्टेज केबलों में आमतौर पर किस इन्सुलेशन सामग्री का उपयोग किया जाता है?
A एक्सएलपीई (क्रॉस-लिंक्ड पॉलीथीन)
B पीवीसी (पॉलीविनाइल क्लोराइड)
C लकड़ी
D रबर
अगला MCQ ↓ Electrical Engineering · High Voltage Engineering
Q112
Hard 2025 ✓ Verified
↗
वोल्टेज मल्टीप्लायर सर्किट में उच्च स्तर पर शिथिलता को कैसे कम किया जा सकता है?
A उच्च चरणों में धारिता को कम करके
B निचले चरणों में धारिता को कम करके
C उच्च चरणों में धारिता बढ़ाकर
D निचले चरणों में धारिता बढ़ाकर
अगला MCQ ↓ Electrical Engineering · High Voltage Engineering
Q113
Moderate 2025 ✓ Verified
↗
__________ is the normal length of the cable sample used for testing.
A 1 - 50 cm
B 50cm - 10 m
C 10 - 100 m
D Above 100 m
अगला MCQ ↓ Electrical Engineering · High Voltage Engineering
Q114
Easy 2025 ✓ Verified
↗
__________ finds the deterioration or failure due to internal discharges caused in the insulation of bushing.
A Power-factor voltage test
B Internal or partial discharge test
C Visible discharge test
D Momentary withstand test
अगला MCQ ↓ Electrical Engineering · High Voltage Engineering
Q115
Easy 2025 ✓ Verified
↗
RMS value is defined based on which of the following?
A Heating effect
B Charge transfer
C Current
D Voltage
अगला MCQ ↓ Electrical Engineering · AC Fundamentals
Q116
Moderate 2025 ✓ Verified
↗
A physical system of electromechanical energy conversion consists of a stationary part creating a magnetic field with electric energy input, and a moving part giving mechanical energy output. If the movable part is kept fixed, the entire electrical energy input will be _______
A Stored in the magnetic field
B Stored in the electric field
C Divided equally between the magnetic and electric fields
D Zero
अगला MCQ ↓ Electrical Engineering · Electromechanical Energy Conversion
Q117
Easy 2025 ✓ Verified
↗
निम्नलिखित में से किसकी परिचालन लागत सबसे अधिक है?
A पनबिजली संयंत्र
B थर्मल पावर प्लांट
C परमाणु ऊर्जा संयंत्र
D सौर विद्युत ऊर्जा संयंत्र
अगला MCQ ↓ Electrical Engineering · Power Plant Economics
Q118
Easy 2025 ✓ Verified
↗
निम्नलिखित में से कौन सा वार्षिक औसत भार दर्शाता है?
A (एक दिन में kWh आपूर्ति) / 24
B {(एक दिन में kWh आपूर्ति) / 24} × 365
C {(एक महीने में किलोवाट आपूर्ति) / (30 × 24)
D (किलोवाट एक वर्ष में आपूर्ति) / (24 × 365)
अगला MCQ ↓ Electrical Engineering · Load Curves and Tariffs
Q119
Easy 2025 ✓ Verified
↗
निम्नलिखित में से किसे शीत आरक्षित कहा जाता है?
A आरक्षित क्षमता उपलब्ध है लेकिन उपयोग के लिए तैयार नहीं है
B आरक्षित क्षमता उपलब्ध है और उपयोग के लिए तैयार है
C जनरेटिंग क्षमता बस से जुड़ी हुई है और लोड लेने के लिए तैयार है
D पीक लोड से अधिक सेवा में क्षमता
अगला MCQ ↓ Electrical Engineering · Power System Operation
Q120
Easy 2025 ✓ Verified
↗
जब किसी पिंड का संवेग दोगुना हो जाता है, तो उसकी गतिज ऊर्जा ___________ होती है
A वैसा ही रहता है
B शून्य हो जाता है
C इसकी प्रारंभिक गतिज ऊर्जा चार गुना हो जाती है
D इसकी गतिज ऊर्जा दस गुना हो जाती है
अगला MCQ ↓ Electrical Engineering · Engineering Mechanics
Q121
Easy 2025 ✓ Verified
↗
In a thermal power station, coal is used for the generation of electricity. How energy changes from one form to another before it is transformed into electrical energy?
A Heat energy → Mechanical energy → Electrical energy
B Heat energy → Electrical energy → Mechanical energy
C Mechanical energy → Heat energy → Electrical energy
D Electrical energy → Heat energy → Mechanical energy
अगला MCQ ↓ Electrical Engineering · Thermal Power Plants
Q122
Easy 2025 ✓ Verified
↗
भाप विद्युत संयंत्र में बॉयलर का प्राथमिक कार्य क्या है?
A यांत्रिक ऊर्जा को विद्युत ऊर्जा में परिवर्तित करना
B पानी को भाप में बदलने के लिए
C भाप को ठंडा करने के लिए
D भाप का दबाव बढ़ाने के लिए
अगला MCQ ↓ Electrical Engineering · Steam Power Plants
Q123
Easy 2025 ✓ Verified
↗
भाप विद्युत संयंत्र में कंडेनसर का उद्देश्य क्या है?
A भाप को वापस पानी में बदलने के लिए
B भाप का तापमान बढ़ाने के लिए
C बिजली पैदा करने के लिए
D टरबाइन की गति को नियंत्रित करने के लिए
अगला MCQ ↓ Electrical Engineering · Steam Power Plants
Q124
Easy 2025 ✓ Verified
↗
निम्नलिखित में से कौन सा भाप बिजली संयंत्र में उपयोग किया जाने वाला ईंधन का प्रकार नहीं है?
A कोयला
B प्राकृतिक गैस
C यूरेनियम
D तेल
अगला MCQ ↓ Electrical Engineering · Steam Power Plants
Q125
Easy 2025 ✓ Verified
↗
What is the efficiency of a typical steam power plant?
A 10-20%
B 30-40%
C 50-60%
D 70-80%
अगला MCQ ↓ Electrical Engineering · Steam Power Plants
Q126
Easy 2025 ✓ Verified
↗
What is the function of a cooling tower in a steam power plant?
A To cool down the steam
B To cool down the water from the condenser
C To generate electricity
D To control the pressure of the steam
अगला MCQ ↓ Electrical Engineering · Steam Power Plants
Q127
Easy 2025 ✓ Verified
↗
एक नई नवीकरणीय ऊर्जा प्रणाली पवन से ऊर्जा प्राप्त करने के लिए डिज़ाइन की गई है। सिस्टम को बनाने के लिए आवश्यक कुल ऊर्जा 240 kJ है। सिस्टम का ऊर्जा उपज अनुपात 14:3 है। अपने जीवनकाल में सिस्टम द्वारा प्रदान की गई कुल ऊर्जा क्या होगी?
A 1,120 के.जे
B 18,000 के.जे
C 2,258 के.जे
D 54,000 के.जे
अगला MCQ ↓ Electrical Engineering · Renewable Energy
Q128
Easy 2025 ✓ Verified
↗
Which of the following is the 7th goal of the eight millennium goals of United Nations?
A To eradicate extreme poverty and hunger
B To ensure environment sustainability
C To reduce child mortality
D To develop a global partnership for development
अगला MCQ ↓ Electrical Engineering · Sustainable Development
Q129
Easy 2025 ✓ Verified
↗
What is the aim of Paris Agreement in 2015? (Note : C indicates Celsius)
A To keep the decrease in global average temperature to below 2 degree C
B To keep the decrease in global average temperature to above 2 degree C
C To keep the increase in global average temperature to above 2 degree C
D To keep the increase in global average temperature to below 2 degree C
अगला MCQ ↓ Electrical Engineering · Climate Policy
Q130
Easy 2025 ✓ Verified
↗
भारतीय परिवहन क्षेत्र में ऊर्जा की खपत किस पर निर्भर करती है?
A ईंधन की कीमत
B चालक
C एर्गोनॉमिक्स
D ईंधन टैंक
अगला MCQ ↓ Electrical Engineering · Transport Energy
Q131
Easy 2025 ✓ Verified
↗
What is Sun’s declination angle during summer solstice?
A 23.5 degrees
B 0.53 degrees
C 32 minutes
D − 23.5 degrees
अगला MCQ ↓ Electrical Engineering · Solar Energy
Q132
Easy 2025 ✓ Verified
↗
What does the term “Quality Control” mean in the context of Industrial Engineering and Management?
A Maintaining product standards and consistency
B Financial risk analysis
C Ensuring employee satisfaction
D Monitoring production costs
अगला MCQ ↓ Electrical Engineering · Quality Management
Q133
Easy 2025 ✓ Verified
↗
The primary objective of the __________ is to consolidate the laws relating to the generation, transmission, distribution, trading and use of electricity in India.
A Energy Conservation Act, 2001
B Electricity Act, 2003
C Indian Electricity Rules, 1956
D IS 3043
अगला MCQ ↓ Electrical Engineering · Electricity Legislation
Q134
Easy 2025 ✓ Verified
↗
अर्थिंग के लिए भारतीय मानक अभ्यास संहिता __________ में निर्दिष्ट है।
A आईएस 732
B आईएस 3043
C आईएस 1956
D आईएस 2001
अगला MCQ ↓ Electrical Engineering · Indian Standards
Q135
Easy 2025 ✓ Verified
↗
The policy specifically addressing power generation from municipal solid waste in Gujarat is the __________.
A Gujarat Solar Power Policy-2021
B Gujarat Renewable Energy Policy-2023
C Gujarat Waste to Energy Policy-2022
D Gujarat Small Hydel Policy-2016
अगला MCQ ↓ Electrical Engineering · Renewable Energy Policy
Q136
Easy 2025 ✓ Verified
↗
__________ भारत में ऊर्जा के कुशल उपयोग और इसके संरक्षण के लिए प्रावधान करता है।
A विद्युत अधिनियम, 2003
B गुजरात विद्युत उद्योग अधिनियम, 2003
C ऊर्जा संरक्षण अधिनियम, 2001
D भारतीय विद्युत नियम, 1956
अगला MCQ ↓ Electrical Engineering · Energy Legislation
Q137
Easy 2025 ✓ Verified
↗
भारतीय मानक, IS 732 __________ के लिए अभ्यास संहिता प्रदान करता है।
A विद्युत तारों की स्थापना
B अर्थिंग सिस्टम
C सौर पैनल निर्माण
D पवन टरबाइन स्थापना
अगला MCQ ↓ Electrical Engineering · Indian Standards
Q138
Easy 2025 ✓ Verified
↗
A key function of an Electricity Regulatory Commission is the determination of __________.
A Fuel import quotas
B Political election dates
C Tariffs for electricity
D Manufacturing subsidies
अगला MCQ ↓ Electrical Engineering · Electricity Regulation
Q139
Easy 2025 ✓ Verified
↗
गुजरात पवन ऊर्जा नीति वर्ष __________ में स्थापित की गई थी।
A 2016
B 2018
C 2021
D 2023
अगला MCQ ↓ Electrical Engineering · Renewable Energy Policy
Q140
Easy 2025 ✓ Verified
↗
सूची में उल्लिखित गुजरात सौर ऊर्जा नीति __________ में जारी की गई थी।
A 2016
B 2019
C 2021
D 2022
अगला MCQ ↓ Electrical Engineering · Renewable Energy Policy
Q141
Easy 2025 ✓ Verified
↗
पवन सौर हाइब्रिड पावर नीति का प्राथमिक लक्ष्य __________ है।
A कोयला आधारित बिजली संयंत्रों को बढ़ावा देना
B पवन और सौर फार्मों के अलग-अलग विकास को प्रोत्साहित करें
C पवन और सौर ऊर्जा के संयोजन से भूमि और ग्रिड बुनियादी ढांचे का अनुकूलन करें
D सभी नवीकरणीय ऊर्जा को चरणबद्ध तरीके से समाप्त करें
अगला MCQ ↓ Electrical Engineering · Renewable Energy Policy
Q142
Easy 2025 ✓ Verified
↗
The Gujarat Electricity Industry (Reorganization & Regulation) Act was enacted in the year __________.
A 2001
B 1956
C 2003
D 2016
अगला MCQ ↓ Electrical Engineering · Electricity Legislation
Q143
Easy 2025 ✓ Verified
↗
उपकरणों के लिए स्टार लेबलिंग कार्यक्रम, जो ऊर्जा दक्षता का संकेत देता है, __________ के तहत एक महत्वपूर्ण पहल है।
A ऊर्जा दक्षता ब्यूरो (बीईई)
B गुजरात ऊर्जा विकास एजेंसी (जीईडीए)
C केंद्रीय विद्युत प्राधिकरण (सीईए)
D भारतीय मानक संस्थान (आईएसआई)
अगला MCQ ↓ Electrical Engineering · Energy Efficiency
Q144
Easy 2025 ✓ Verified
↗
The Gujarat Small Hydel Policy of 2016 typically applies to hydroelectric projects with a station capacity upto __________.
A 10 MW
B 25 MW
C 50 MW
D 100 MW
अगला MCQ ↓ Electrical Engineering · Renewable Energy Policy
Q145
Moderate 2025 ✓ Verified
↗
IS 3043 के अनुसार, एक बड़े पावर स्टेशन के लिए अर्थ कनेक्शन का प्रतिरोध जितना संभव हो उतना कम होना चाहिए, आदर्श रूप से __________ से अधिक नहीं होना चाहिए।
A 0.5 Ω
B 2.0 Ω
C 5.0 Ω
D 10.0 Ω
अगला MCQ ↓ Electrical Engineering · Indian Standards
Q146
Easy 2025 ✓ Verified
↗
विद्युत अपीलीय न्यायाधिकरण (एपीटीईएल) की स्थापना __________ द्वारा अनिवार्य की गई थी।
A भारतीय विद्युत नियम, 1956
B ऊर्जा संरक्षण अधिनियम, 2001
C विद्युत अधिनियम, 2003
D आईएस 732
अगला MCQ ↓ Electrical Engineering · Electricity Legislation
Q147
Easy 2025 ✓ Verified
↗
As per IS 732, the colour code for the earth wire in a flexible cable is __________.
A Red
B Black
C Green
D Blue
अगला MCQ ↓ Electrical Engineering · Indian Standards
Q148
Easy 2025 ✓ Verified
↗
The Gujarat Renewable Energy Policy of 2023 was introduced to supersede previous policies and attract __________ in the RE sector.
A Foreign tourists
B Massive investments
C Agricultural workers
D IT companies
अगला MCQ ↓ Electrical Engineering · Renewable Energy Policy
Q149
Easy 2025 ✓ Verified
↗
1956 के भारतीय विद्युत नियम काफी हद तक बिजली क्षेत्र में __________ सुनिश्चित करने पर केंद्रित थे।
A लाभप्रदता
B सुरक्षा और आपूर्ति मानक
C प्रतियोगिता
D निजीकरण
अगला MCQ ↓ Electrical Engineering · Electricity Legislation
Q150
Easy 2025 ✓ Verified
↗
नई व्यावसायिक इमारतों के लिए ऊर्जा प्रदर्शन मानक निर्धारित करने के लिए ऊर्जा संरक्षण भवन कोड (ECBC) __________ द्वारा लॉन्च किया गया था।
A ऊर्जा दक्षता ब्यूरो (बीईई)
B आवास और शहरी मामलों का मंत्रालय
C गुजरात रेरा
D जीईडीए
अगला MCQ ↓ Electrical Engineering · Energy Efficiency
Q151
Easy 2025 ✓ Verified
↗
The Gujarat Wind Power Policy of 2016 included provisions for the 'repowering' of older, less efficient __________.
A Solar panels
B Wind turbines
C Hydro plants
D Transformers
अगला MCQ ↓ Electrical Engineering · Renewable Energy Policy
Q152
Easy 2025 ✓ Verified
↗
The primary purpose of equipment earthing as per IS 3043 is to __________.
A Improve the power factor
B Provide a safe path for leakage/fault current to flow
C Stabilize the system frequency
D Reduce the electricity bill
अगला MCQ ↓ Electrical Engineering · Earthing and Safety
Q153
Easy 2025 ✓ Verified
↗
गुजरात सौर ऊर्जा नीति, 2021 की अवधि __________ है।
A 2 साल
B 3 साल
C 5 साल
D 10 साल
अगला MCQ ↓ Electrical Engineering · Renewable Energy Policy
Q154
Easy 2025 ✓ Verified
↗
The policy that allows for setting up wind and solar projects at the same location to save land and transmission infrastructure is the __________.
A Gujarat Small Hydel Policy, 2016
B Gujarat Wind Solar Hybrid Power Policy, 2018-19
C Gujarat Waste to Energy Policy, 2022
D Gujarat Solar Power Policy, 2021
अगला MCQ ↓ Electrical Engineering · Renewable Energy Policy
Q155
Moderate 2025 ✓ Verified
↗
IS 732 के अनुसार, किसी इंस्टॉलेशन में लीकेज करंट पूर्ण लोड करंट के __________ से अधिक नहीं होना चाहिए।
A 1/500वां
B 1/1000वां
C 1/5000वां
D 1/100वां
अगला MCQ ↓ Electrical Engineering · Indian Standards
Q156
Easy 2025 ✓ Verified
↗
The creation of a National Load Despatch Centre and Regional Load Despatch Centres is mandated by the __________.
A Energy Conservation Act, 2001
B Electricity Act, 2003
C Indian Electricity Rules, 1956
D IS 3043
अगला MCQ ↓ Electrical Engineering · Electricity Legislation
Q157
Easy 2025 ✓ Verified
↗
The main objective of the Gujarat Electricity Industry (Reorganization & Regulation) Act, 2003 was aligned with the national policy of __________.
A Increasing coal imports
B Power sector reforms
C Banning all private players
D Nationalizing all power plants
अगला MCQ ↓ Electrical Engineering · Electricity Legislation
Q158
Moderate 2025 ✓ Verified
↗
'परफॉर्म, अचीव एंड ट्रेड' (PAT) योजना बड़े उद्योगों में ऊर्जा दक्षता में सुधार के लिए एक बाजार-आधारित तंत्र है और __________ का एक हिस्सा है।
A विद्युत अधिनियम, 2003
B जलवायु परिवर्तन पर राष्ट्रीय कार्य योजना (बीईई के तहत)
C गुजरात अपशिष्ट से ऊर्जा नीति
D भारतीय विद्युत नियम, 1956
अगला MCQ ↓ Electrical Engineering · Energy Efficiency
Q159
Easy 2025 ✓ Verified
↗
The Gujarat Energy Development Agency (GEDA) is primarily focused on __________.
A Regulating electricity tariffs
B Promoting energy conservation and renewable energy
C Operating large thermal power plants
D Managing the state's power grid
अगला MCQ ↓ Electrical Engineering · Renewable Energy Institutions
Q160
Easy 2025 ✓ Verified
↗
इलेक्ट्रोमैकेनिकल लिफ्ट प्रणाली में, गवर्नर का प्राथमिक कार्य क्या है?
A दरवाजे खोलने और बंद करने के लिए
B मंजिल संख्या इंगित करने के लिए
C ओवरस्पीडिंग की स्थिति में सुरक्षा ब्रेक को सक्रिय करने के लिए
D लिफ्ट की आंतरिक प्रकाश व्यवस्था को नियंत्रित करने के लिए
अगला MCQ ↓ Electrical Engineering · Vertical Transportation
Q161
Easy 2025 ✓ Verified
↗
What is the typical angle of inclination for a commercial escalator as per general safety standards?
A 15 degrees
B 30 degrees
C 45 degrees
D 60 degrees
अगला MCQ ↓ Electrical Engineering · Vertical Transportation
Q162
Easy 2025 ✓ Verified
↗
सेंट्रल एयर कंडीशनिंग सिस्टम में कौन सा घटक रेफ्रिजरेंट से गर्मी हटाने के लिए जिम्मेदार है?
A बाष्पीकरण करनेवाला
B कंप्रेसर
C विस्तार वाल्व
D संघनित्र
अगला MCQ ↓ Electrical Engineering · HVAC
Q163
Easy 2025 ✓ Verified
↗
एनबीसी 2016 के अनुसार, निम्नलिखित में से किसे एक आवश्यक भार माना जाता है जिसे आपातकालीन बिजली प्रणाली से जोड़ा जाना चाहिए?
A सामान्य कार्यालय कार्यस्थान
B वाटर कूलर
C फायर पंप और फायर अलार्म
D सजावटी प्रकाश व्यवस्था
अगला MCQ ↓ Electrical Engineering · Building Safety
Q164
Easy 2025 ✓ Verified
↗
The 'cone of protection' method, specified in lightning protection standards, is used to determine the area protected by a
A Surge protector
B Lightning rod (air terminal)
C Grounding wire
D Fuse
अगला MCQ ↓ Electrical Engineering · Lightning Protection
Q165
Easy 2025 ✓ Verified
↗
किसी व्यावसायिक भवन में डीजल जेनरेटर (डीजी) सेट का मुख्य उद्देश्य क्या है?
A दैनिक बिजली बिल को कम करने के लिए
B संपूर्ण भवन को प्राथमिक शक्ति प्रदान करना
C ग्रिड आउटेज के दौरान बैकअप पावर स्रोत के रूप में कार्य करना
D केवल एचवीएसी प्रणाली को बिजली देने के लिए
अगला MCQ ↓ Electrical Engineering · Standby Power
Q166
Easy 2025 ✓ Verified
↗
विद्युत प्रणाली में आरसीसीबी (अवशिष्ट धारा सर्किट ब्रेकर) का प्राथमिक कार्य क्या है?
A ओवर-वोल्टेज से बचाने के लिए
B शॉर्ट सर्किट से बचाने के लिए
C उच्च-आवृत्ति शोर से बचाने के लिए
D पृथ्वी दोष के कारण मनुष्यों को बिजली के झटके से बचाने के लिए
अगला MCQ ↓ Electrical Engineering · Electrical Protection
Q167
Easy 2025 ✓ Verified
↗
Which system is considered the central 'brain' for controlling and monitoring a building's mechanical and electrical equipment such as ventilation, lighting and power systems?
A CCTV System
B Public Address System
C Building Management System (BMS)
D Fire Alarm System
अगला MCQ ↓ Electrical Engineering · Building Automation
Q168
Easy 2025 ✓ Verified
↗
निम्नलिखित में से क्या आमतौर पर किसी भवन के ऑडियो-वीडियो (एवी) सिस्टम द्वारा नियंत्रित नहीं किया जाता है?
A सम्मेलन कक्ष में प्रोजेक्टर और स्क्रीन
B बैकग्राउंड म्यूजिक सिस्टम
C वीडियो कॉन्फ्रेंसिंग उपकरण
D इमारत का अग्नि हाइड्रेंट दबाव
अगला MCQ ↓ Electrical Engineering · ELV Systems
Q169
Easy 2025 ✓ Verified
↗
कंप्यूटर नेटवर्किंग में, किस टोपोलॉजी में सभी उपकरणों को गोलाकार तरीके से जोड़ना शामिल है?
A सितारा
B बस
C अंगूठी
D जाल
अगला MCQ ↓ Electrical Engineering · Computer Networking
Q170
Moderate 2025 ✓ Verified
↗
भारत के राष्ट्रीय विद्युत संहिता (एनईसी), 2023 में पेश किया गया फोकस का प्रमुख क्षेत्र क्या है?
A सभी गरमागरम प्रकाश व्यवस्था को चरणबद्ध तरीके से बंद करना
B तारों के विशिष्ट ब्रांडों को अनिवार्य करना
C विद्युत वाहन चार्जिंग बुनियादी ढांचे के लिए विनियम
D एल्युमीनियम वायरिंग के उपयोग पर प्रतिबंध
अगला MCQ ↓ Electrical Engineering · Electrical Codes
Q171
Easy 2025 ✓ Verified
↗
What is the main function of a Manual Call Point (MCP) in a fire alarm system?
A To automatically detect smoke
B To allow a person to manually trigger the fire alarm
C To silence the alarm after an incident
D To test the sprinkler system
अगला MCQ ↓ Electrical Engineering · Fire Alarm Systems
Q172
Easy 2025 ✓ Verified
↗
Which lamp technology is currently the most energy-efficient and widely adopted for new street lighting projects?
A High-Pressure Sodium (HPS)
B Mercury Vapor
C Metal Halide
D Light Emitting Diode (LED)
अगला MCQ ↓ Electrical Engineering · Lighting
Q173
Easy 2025 ✓ Verified
↗
In street lighting, the term 'luminaire' refers to
A Only the light bulb or lamp
B The supporting pole
C The complete lighting fixture including the lamp, housing and reflector
D The underground electrical cable
अगला MCQ ↓ Electrical Engineering · Lighting
Q174
Easy 2025 ✓ Verified
↗
ऊंची इमारतों की जल आपूर्ति प्रणालियों में पानी का दबाव बढ़ाने के लिए किस प्रकार के पंप का सबसे अधिक उपयोग किया जाता है?
A प्रत्यावर्ती पंप
B सबमर्सिबल पंप
C केन्द्रापसारक पम्प
D डायाफ्राम पंप
अगला MCQ ↓ Electrical Engineering · Water Supply Systems
Q175
Easy 2025 ✓ Verified
↗
किसी पंप का 'कुल हेड' क्या दर्शाता है?
A पंप का भौतिक आकार
B मोटर की घूर्णन गति
C कुल ऊंचाई जिस तक एक पंप पानी ले जा सकता है, घर्षण हानि के लिए लेखांकन
D यह प्रति मिनट जितना पानी ले जा सकता है
अगला MCQ ↓ Electrical Engineering · Pumps
Q176
Moderate 2025 ✓ Verified
↗
गैलियम नाइट्राइड (GaN) जैसे वाइड-बैंडगैप (WBG) सेमीकंडक्टर मुख्य रूप से पावर इलेक्ट्रॉनिक्स में लोकप्रिय हो रहे हैं क्योंकि वे _________ प्रदान करते हैं
A सिलिकॉन की तुलना में कम लागत
B पावर कन्वर्टर्स के लिए उच्च दक्षता और छोटा आकार
C आसान विनिर्माण प्रक्रियाएं
D बहुत कम तापमान पर बेहतर प्रदर्शन
अगला MCQ ↓ Electrical Engineering · Semiconductor Devices
Q177
Easy 2025 ✓ Verified
↗
मोबाइल उपकरणों के लिए अधिकांश सामान्य वायरलेस चार्जिंग पैड के संचालन का सिद्धांत पर आधारित है
A स्थैतिक बिजली
B विद्युत चुम्बकीय प्रेरण
C सौर विकिरण
D पीजोइलेक्ट्रिक प्रभाव
अगला MCQ ↓ Electrical Engineering · Emerging Electrical Technologies
Q178
Easy 2025 ✓ Verified
↗
ट्रैक्शन लिफ्ट में, काउंटरवेट का क्या कार्य है?
A यह एक आपातकालीन ब्रेक के रूप में कार्य करता है
B यह ऊर्जा बचाने के लिए लिफ्ट कार के वजन और उसके भार के एक हिस्से को संतुलित करता है
C इसमें लिफ्ट कंट्रोल पैनल है
D यह लिफ्ट के लिए बिजली उत्पन्न करता है
अगला MCQ ↓ Electrical Engineering · Vertical Transportation
Q179
Easy 2025 ✓ Verified
↗
एचवीएसी में एक वेरिएबल एयर वॉल्यूम (वीएवी) प्रणाली को डिज़ाइन किया गया है
A प्रवाह को स्थिर रखते हुए हवा का तापमान बदलते रहें
B किसी क्षेत्र की तापमान आवश्यकताओं के आधार पर वायु प्रवाह में परिवर्तन करें
C वायु आपूर्ति की आर्द्रता में परिवर्तन करें
D केवल दो गतियों, उच्च और निम्न, पर काम करें
अगला MCQ ↓ Electrical Engineering · HVAC
Q180
Moderate 2025 ✓ Verified
↗
0.9 पावर फैक्टर पर 10 किलोवाट की इनपुट शक्ति के साथ एक संतुलित तीन चरण, तीन तार प्रणाली के लिए, दोनों वाटमीटर पर रीडिंग क्रमशः _________ हैं
A 7 किलोवाट, 3 किलोवाट
B 5000 डब्ल्यू, 5000 डब्ल्यू
C 7600 डब्लू, 1200 डब्लू
D 6350 डब्लू, 3650 डब्लू
Electrical Engineering · Three-Phase Circuits